T: 01858 410 372
E: techenquiries@radmat.com
sales@radmat.com

EshaFlex System

Quick Links

Reinforced Bitumen Membrane EshaFlex_logo SBS modified Reinforced Bitumen Membranes for use as partially bonded, fully bonded or mechanically fixed roof waterproofing on zero falls, flat or pitched roofs. Suitable for refurbishment, new build and green roof applications. EshaFlex membranes are BBA Certified for ‘in excess of 30 years’ and can achieve a BRE Green Guide to Specification A+ ratings. EshaFlex membranes feature Groove Technology®, a patented underside finish that ensures the heat acts only where it is needed, reducing warming of the membrane, increasing melting of the PE foil. In application this means that EshaFlex membranes require up to 45 grams per m² (25%) less gas, reduce CO2 production by up to 168 g/m² reducing installation times by up to 30%.

EshaFlex Overlay System

EshaFlex Overlay Systems provide a cost effective way to upgrade an existing bituminous or asphalt roof with limited disruption or alteration. They are installed over a suitably prepared existing roof surface, a Radmat Total Care survey is required to assess condition and suitability.

Click on the tabs below to see the options for Overlay Systems.

Partially Bonded Single Layer System

APPLICATION

Use when overlaying existing bituminous or asphalt waterproofing systems that have suffered failures or are likely to contain water or water vapour.

WATERPROOFING

Apply Esha Primer to all existing surfaces followed by EshaFlex TK60 black Mineral reinforced bitumen membrane torch bonded. All upstands will require a primary layer of EshaFlex 370 Plain base layer and EshaFlex 370 Black Mineral as the Cap Sheet.

Read more about EshaFlex cap sheets here.

GENERAL

A fast, efficient and cost effective way to extend the life of an existing roof with minimal disruption. Esha Reinforced Bitumen Membranes are BBA Certified to have a durability of ‘in excess of 30 years‘. To increase the thermal performance click the Upgrade & New Build Systems tab, alternatively to look at adding a Green Roof Systems select that tab.

QUICK LINKS

Fully bonded Single Layer System

APPLICATION

Use when overlaying existing bituminous or asphalt waterproofing systems that have suffered failures but unlikely to contain water or water vapour.

WATERPROOFING

Apply Esha Primer to all existing surfaces followed by EshaFlex 370 Black Mineral as the Cap Sheet torch bonded. All upstands will require a primary layer of EshaFlex 370 Plain base layer and EshaFlex 370 Black Mineral as the Cap Sheet.

Read more about EshaFlex cap sheets here.

GENERAL

On tall buildings, or in areas of high wind uplift, a fully bonded membrane offers long term security and extends the life of an existing roof with minimal disruption. Esha Reinforced Bitumen Membranes are BBA Certified to have a durability of ‘in excess of 30 years’. To increase the thermal performance click the Upgrade & New Build Systems tab, alternatively to look at adding a Green Roof Systems select that tab.

QUICK LINKS

EshaFlex Upgrade & New Build Systems

EshaFlex Upgrade Systems provide an efficient way of improving the thermal efficiency of an existing building, reducing the annual heat energy costs. They are installed over a suitably prepared existing roof surface, a Radmat Total Care survey is required to assess condition and suitability.

In New build a Radmat Area Technical Manager will work with the specifier to develop a specification and consult on detail design, thermal calculations etc.

Green Roof Systems are available for Overlay, Upgrade & New Build applications.

Click on the tabs below to see the options for Upgrade Systems.

Partially Bonded Two Layer System

APPLICATION

Suitable for new build and refurbishment applications over numerous roof types, a slope in the roof substrate or insulation will be required.

CAP SHEET

EshaFlex 370 Black Mineral or EshaFlex 370 Grey Mineral reinforced bitumen membrane torch applied to base sheet. Featuring patented Esha Groove Technology® which uses up to 25% less gas, reduce CO2 production by up to 168 g/m2 and reduce installation times by up to 30%.

Read more about EshaFlex cap sheets here.

BASE SHEET

Prime the surface of the insulation with EshaPrimer and then apply EshaVent partially bonded base sheet providing 40% bond area. Release film on underside is removed when installed over a primed surface, thermo adhesive bonding as cap sheet is torched.

INSULATION

ProTherm polyisocyanurate (PIR) insulation to a thickness specified to achieve the U value (See Thermal calculation tab)manufactured from CFC and HCFC free grade of material to ensure zero ozone depletion potential and a global warming potential factor less than 5 and with a BRE Green Guide A rating. Either a uniform thickness as part of a sloping substrate or tapered to create the fall.

VAPOUR LAYER

A choice of four:
EshaBase 2mm Alu SA; Following an application of Esha SA Primer a self-adhesive aluminum lined reinforced vapour layer applied to lightweight timber, concrete or panel substrates.

EshaBase 4.2mm Alu SA; Following an application of Esha SA Primer a self-adhesive aluminum lined reinforced vapour layer applied to lightweight metal decks, timber, concrete or panel substrates.

EshaBase SA Sand; Following an application of Esha SA Primer a self-adhesive sand faced vapour layer applied to lightweight timber, concrete or panel substrates.

EshaBase Alu; Following an application of Esha Primer a reinforced aluminum lined vapour layer torch applied to a solid substrate.

UPSTANDS

After the placement of an Esha tilting fillet to the intersection of upstands install EshaFlex 370 Plain followed by Eshaflex 370 Black or Grey Mineral, both torch applied.

QUICK LINKS

Fully Bonded Two Layer System

APPLICATION

Suitable for new build and refurbishment applications over numerous roof types. May be used when the slope in the roof exceeds 10 degrees and extra bonding restraint is required.

CAP SHEET

EshaFlex 370 Black Mineral or EshaFlex 370 Grey Mineral reinforced bitumen membrane torch applied to base sheet. Featuring patented Esha Groove Technology® which uses up to 25% less gas, reduce CO2 production by up to 168 g/m2 and reduce installation times by up to 30%.

Read more about EshaFlex cap sheets here.

BASE SHEET

Primer the surface of the insulation with EshaPrimer and then apply EshaFlex 370 Plain fully bonded base sheet providing 100% bond area.

INSULATION

ProTherm polyisocyanurate (PIR) insulation to a thickness specified to achieve the U value (See Thermal calculation tab) manufactured from CFC and HCFC free grade of material to ensure zero ozone depletion potential and a global warming potential factor less than 5 and with a BRE Green Guide A rating. Either a uniform thickness as part of a sloping substrate or tapered to create the fall.

VAPOUR LAYER

A choice of four:
EshaBase 2mm Alu SA; Following an application of Esha SA Primer a self-adhesive aluminum lined reinforced vapour layer applied to lightweight timber, concrete or panel substrates.

EshaBase 4.2mm Alu SA; Following an application of Esha SA Primer a self-adhesive aluminum lined reinforced vapour layer applied to lightweight metal decks, timber, concrete or panel substrates.

EshaBase SA Sand; Following an application of Esha SA Primer a self-adhesive sand faced vapour layer applied to lightweight timber, concrete or panel substrate/growing medium.

EshaBase Alu; Following an application of Esha Primer a reinforced aluminum lined vapour layer torch applied to a solid substrate.

UPSTANDS

After the placement of an Esha tilting fillet to the intersection of upstands install EshaFlex 370 Plain followed by Eshaflex 370 Black or Grey Mineral, both torch applied.

QUICK LINKS

Self-adhered Two Layer System

APPLICATION

Suitable for new build and refurbishment applications over numerous roof types. A flame free fully bonded two layer system.

CAP SHEET

EshaFlex 370 SA Black Mineral reinforced bitumen membrane fully bonded cap sheet providing 100% bond area. Release film on underside is removed when installed over the Esha SA primed base layer surface.

Read more about EshaFlex cap sheets here.

BASE SHEET

Primer the surface of the insulation with EshaPrimer and then apply EshaBase SA Sand fully bonded base sheet providing 100% bond area. Release film on underside is removed when installed over the Esha SA primed insulation surface.

INSULATION

ProTherm polyisocyanurate (PIR) insulation to a thickness specified to achieve the U value (See Thermal calculation tab)manufactured from CFC and HCFC free grade of material to ensure zero ozone depletion potential and a global warming potential factor less than 5 and with a BRE Green Guide A rating. Either a uniform thickness as part of a sloping substrate or tapered to create the fall.

VAPOUR LAYER

A choice of three:
EshaBase 2mm Alu SA; Following an application of Esha SA Primer a self-adhesive aluminum lined reinforced vapour layer applied to lightweight timber, concrete or panel substrates.

EshaBase 4.2mm Alu SA; Following an application of Esha SA Primer a self-adhesive aluminum lined reinforced vapour layer applied to lightweight metal decks, timber, concrete or panel substrates.

EshaBase SA Sand; Following an application of Esha SA Primer a self-adhesive sand faced vapour layer applied to lightweight timber, concrete or panel substrates.

UPSTANDS

After the placement of an Esha tilting fillet to the intersection of upstands install EshaBase SA Sand followed by EshaFlex 370 SA Black Mineral.

QUICK LINKS

Zero-fall Partially Bonded Three Layer System

APPLICATION

Suitable for new build and refurbishment applications over numerous roof types. For use on terrace areas and balconies, subsequently covered timber or paved decking.

CAP SHEET

EshaFlex 370 Black Mineral or EshaFlex 370 Grey Mineral reinforced bitumen membrane torch applied to base layer. Featuring patented Esha Groove Technology® which uses up to 25% less gas, reduce CO2 production by up to 168 g/m2 and reduce installation times by up to 30%.

Read more about EshaFlex cap sheets here.

BASE SHEET 2

EshaFlex 370 reinforced bitumen membrane torch applied to Base Layer 1.

BASE SHEET 1

Primer the surface of the insulation with EshaPrimer and then apply EshaVent partially bonded base sheet providing 40% bond area. Release film on underside is removed when installed over a primed surface, thermo adhesive bonding as cap sheet is torched.

INSULATION

ProTherm polyisocyanurate (PIR) insulation to a thickness specified to achieve the U value (See Thermal calculation tab)manufactured from CFC and HCFC free grade of material to ensure zero ozone depletion potential and a global warming potential factor less than 5 and with a BRE Green Guide A rating. Either a uniform thickness as part of a sloping substrate or tapered to create the fall.

VAPOUR LAYER

A choice of three:
EshaBase 2mm Alu SA; Following an application of Esha SA Primer a self-adhesive aluminum lined reinforced vapour layer applied to lightweight timber, concrete or panel substrates.

EshaBase 4.2mm Alu SA; Following an application of Esha SA Primer a self-adhesive aluminum lined reinforced vapour layer applied to lightweight metal decks, timber, concrete or panel substrates.

EshaBase Alu; Following an application of Esha SA Primer a torch-on sand faced vapour layer applied to lightweight timber, concrete or panel substrates.

UPSTANDS

After the placement of an Esha tilting fillet to the intersection of upstands install EshaFlex 370 Plain followed by Eshaflex 370 Black or Grey Mineral, both torch applied.

QUICK LINKS

Inverted Two Layer System

APPLICATION

Suitable for new build and refurbishment applications over numerous roof types.

INSULATION

ProTherm inverted roof insulation is a rigid, closed cell type Extruded polystyrene board with integral high density skin and drainage grooves. ProTherm inverted roof insulation has a Zero Ozone Depletion Potential (ODP), a Global Warming Potential (GWP) of less than 5 and a Green Guide to Specification A rating.

CAP SHEET

EshaFlex 370 Plain reinforced bitumen membrane torch applied to base layer. Featuring patented Esha Groove Technology® which uses up to 25% less gas, reduce CO2 production by up to 168 g/m2 and reduce installation times by up to 30%.

Read more about EshaFlex cap sheets here.

BASE SHEET

EshaFlex 370 Plain reinforced bitumen membrane torch applied to primed concrete surface.

INSULATION

ProTherm G provides the highest thermal performance per mm of any XPS insulation, and is fire resistant.
ProTherm Quantum VIP provides the thinnest inverted roof system in the world, whilst meeting the requirements of Building Regulations Part L, Part M and NHBC Chapter 7.1.
Read more about the guaranteed range of ProTherm insulants here.

UPSTANDS

After the placement of an Esha tilting fillet to the intersection of upstands install EshaFlex 370 Plain followed by EshaFlex 370 Black Mineral.

QUICK LINKS

EshaFlex Green Roof System

MedO Green Roof Systems comprise a range of extensive, wildflower, biodiverse and intensive green roof systems that provide a range of environmental, aesthetic, amenity and performance benefits.

Click on the tabs below to see the various EshaUniversal membranes suitable for use with MedO Green Roof Systems.

Partially Bonded Two Layer System

APPLICATION

Suitable for new build and refurbishment applications over numerous roof types, a slope in the roof substrate or insulation will be required.

CAP SHEET

Radmat Texsa Root Barrier P Reinforced Bitumen Membrane torch applied to base sheet. Texsa Root Barrier P is BS EN 13948: 2007 compliant for resistance to root penetration.

Read more about EshaFlex cap sheets here.

BASE SHEET

Primer the surface of the insulation with EshaPrimer and then apply EshaTherm TK40 partially bonded base sheet providing 40% bond area. Release film on underside is removed when installed over a primed surface, thermo adhesive bonding as cap sheet is torched.

INSULATION

ProTherm polyisocyanurate (PIR) insulation to a thickness specified to achieve the U value (See Thermal calculation tab)manufactured from CFC and HCFC free grade of material to ensure zero ozone depletion potential and a global warming potential factor less than 5 and with a BRE Green Guide A rating. Either a uniform thickness as part of a sloping substrate or tapered to create the fall.

VAPOUR LAYER

A choice of four:
EshaBase 2mm Alu SA; Following an application of Esha SA Primer a self-adhesive aluminum lined reinforced vapour layer applied to lightweight timber, concrete or panel substrates.

EshaBase 4.2mm Alu SA; Following an application of Esha SA Primer a self-adhesive aluminum lined reinforced vapour layer applied to lightweight metal decks, timber, concrete or panel substrates.

EshaBase SA Sand; Following an application of Esha SA Primer a self-adhesive sand faced vapour layer applied to lightweight timber, concrete or panel substrates.

EshaBase Alu; Following an application of Esha Primer a reinforced aluminum lined vapour layer torch applied to a solid substrate.

UPSTANDS

After the placement of a ProTherm Angle Fillet to the intersection of upstands install EshaFlex 370 Plain followed by Radmat Texsa Root Barrier P, both torch applied.

QUICK LINKS

Fully Bonded Two Layer System

APPLICATION

Suitable for new build and refurbishment applications over numerous roof types. May be used when the slope in the roof exceeds 10 degrees and extra bonding restraint is required.

CAP SHEET

Radmat Texsa Root Barrier P Reinforced Bitumen Membrane torch applied to base sheet. Texsa Root Barrier P is BS EN 13948: 2007 compliant for resistance to root penetration.

Read more about EshaFlex cap sheets here

BASE SHEET

Primer the surface of the insulation with EshaPrimer and then apply EshaFlex 370 Plain fully bonded base sheet providing 100% bond area.

INSULATION

ProTherm polyisocyanurate (PIR) insulation to a thickness specified to achieve the U value (See Thermal calculation tab)manufactured from CFC and HCFC free grade of material to ensure zero ozone depletion potential and a global warming potential factor less than 5 and with a BRE Green Guide A rating. Either a uniform thickness as part of a sloping substrate or tapered to create the fall.

VAPOUR LAYER

A choice of four:
EshaBase 2mm Alu SA; Following an application of Esha SA Primer a self-adhesive aluminum lined reinforced vapour layer applied to lightweight timber, concrete or panel substrates.

EshaBase 4.2mm Alu SA; Following an application of Esha SA Primer a self-adhesive aluminum lined reinforced vapour layer applied to lightweight metal decks, timber, concrete or panel substrates.

EshaBase SA Sand; Following an application of Esha SA Primer a self-adhesive sand faced vapour layer applied to lightweight timber, concrete or panel substrates.

EshaBase Alu; Following an application of Esha Primer a reinforced aluminum lined vapour layer torch applied to a solid substrate.

UPSTANDS

After the placement of a ProTherm Angle Fillet to the intersection of upstands install EshaFlex 370 Plain followed by Radmat Texsa Root Barrier P, both torch applied.

QUICK LINKS

Zero-fall Partially Bonded Three Layer System

APPLICATION

Suitable for new build and refurbishment applications over numerous roof types.

Cap Sheet

Radmat Texsa Root Barrier P Reinforced Bitumen Membrane torch applied to base sheet. Texsa Root Barrier P is BS EN 13948: 2007 compliant for resistance to root penetration.

Read more about EshaFlex cap sheets here.

BASE SHEET 1

Primer the surface of the insulation with EshaPrimer and then apply EshaTherm TK40 partially bonded base sheet providing 40% bond area. Release film on underside is removed when installed over a primed surface, thermo adhesive bonding as cap sheet is torched.

BASE SHEET 2

EshaFlex 370 reinforced bitumen membrane torch applied to Base Layer 1

INSULATION

ProTherm polyisocyanurate (PIR) insulation to a thickness specified to achieve the U value (See Thermal calculation tab)manufactured from CFC and HCFC free grade of material to ensure zero ozone depletion potential and a global warming potential factor less than 5 and with a BRE Green Guide A rating. Either a uniform thickness as part of a sloping substrate or tapered to create the fall.

VAPOUR LAYER

A choice of three:
EshaBase 2mm Alu SA; Following an application of Esha SA Primer a self-adhesive aluminum lined reinforced vapour layer applied to lightweight timber, concrete or panel substrates.

EshaBase 4.2mm Alu SA; Following an application of Esha SA Primer a self-adhesive aluminum lined reinforced vapour layer applied to lightweight metal decks, timber, concrete or panel substrates.

EshaBase SA Sand; Following an application of Esha SA Primer a self-adhesive sand faced vapour layer applied to lightweight timber, concrete or panel substrate/growing medium.

UPSTANDS

After the placement of a ProTherm Angle Fillet to the intersection of upstands install EshaFlex 370 Plain followed by Radmat Texsa Root Barrier P, both torch applied.

QUICK LINKS

Cap Sheet

EshaFlex have a range of cap sheets for Overlay, Upgrade & New Build and MedO Green roof systems.

Read more about EshaFlex cap sheets here.

 

WATERPROOFING

Insulation options

Radmat provide a range of thermal insulations for overlay, upgrade and new build green roof systems, all supported by a thermal and condensation risk calculation service for all projects.

Read more about the guaranteed range of ProTherm insulants here.

 

 

INSULATION

The range of Esha vapour layers can provide an effective method of vapour control or a complete vapour barrier.

Read more about Esha vapour layers here.

VAPOUR LAYER

Roof Deck options

Structural concrete decks can be classified as either reinforced (cast in-situ), precast, pre-stressed or lightweight aerated.

Profiled metal deck can be made from steel or aluminium in a variety of thickness and profile.

Composite decks typically comprise an insulation board core sandwiched between factory laminated steel or timber sheet.

Timber decks can be manufactured from eith plywood or Oriented Strand Board (OSB).

Read more about deck options here

ROOF DECK

Roof Light options

ProLight, ProGlaze and ProTube rooflights are suitable for refubishment and new build applications.

ProLight rooflights are manufactured in a variety of shapes and sizes with either extruded polycarbonate or flat glass tops.

Read more

ROOF LIGHTS

Rainwater outlet options

ProFlow rainwater outlets for use with ProGuard leafguards.
Read more

Complementing the ProFlow range of rainwater outlets is a range of leaf guards of different shapes and sizes.

 

RAINWATER OUTLETS

Roof Safety options

Fall Protection

ProSafe Fall Protection

ProSafe Edge Protection

ProSafe Lightning Protection

 

ROOF SAFETY

Approved Contractors

Radmat’s roofing systems can only be installed by our Approved Contractors, companies that are specialists in the roofing sector by one of our Area Technical Managers. 

To find your local Area Technical Manager click here or email techservices@radmat.com.

INSTALLATION
 Sitemap, Quicklinks and Contact Details
© 2024 Radmat Building Products Ltd