DESCRIPTION
ProTherm Quantum® PLUS+ is a rigid Vacuum Insulation Panel (VIP). The VIP panel consists of a compressed fumed silica sand microporous core which is evacuated of air and moisture before being encased and sealed in a special thin, gas-tight, hybrid aluminium foil envelope, encapsulated in a solvent free polyurethane waterproof coating. The coating is a factory applied solvent free two component elastomeric polyurethane waterproofing membrane. The resulting panel gives outstanding thermal conductivity, with the thinnest possible insulation solution.
With a declared (aged) thermal conductivity of 0.007 W/m.K, the ProTherm Quantum® PLUS+ VIP panel provides an insulating performance that is up to five times better than other commonly available insulation materials. This high level of thermal efficiency combined with minimal thickness enable the ProTherm Quantum® PLUS+ VIP Inverted Roof Insulation system to meet the requirements of Building Regulations Part L, Part M and NHBC Chapter 7.1.
BBA Certified 20/5769.
SUITABLE APPLICATIONS
ProTherm Quantum® PLUS+ is suitable for use in roofs, roof terraces, enclosed balconies over heated space and insulated walkways in an inverted roof construction. When used in the inverted roof constructions listed in the Fire Performance section below roof constructions incorporating ProTherm Quantum® PLUS+ achieve Broof(t4) Classification to BS EN 13501-5 as required by Approved Document B 2019 edition, Section B4, Limitations on roof coverings.
ProTherm Quantum® PLUS+ is not suitable for use in inverted roof applications on specified attachments such as projecting open balconies, projecting enclosed balconies, recessed open balconies or recessed enclosed balconies.
FIRE PERFORMANCE
As a roofing system for roofs, roof terraces, enclosed balconies over heated space and insulated walkways
In accordance with Annex of Commission Decision 2000/553/EC, when used in an inverted roof specification including an inorganic covering of either loose laid gravel with a thickness of at least 50mm or a mass ≥ 80 kg/m², sand/cement screed to a thickness of at least 30mm, or cast stone or mineral slabs of at least 40mm thickness a roof system incorporating ProTherm Quantum® PLUS+ can be considered to be unrestricted under the national Requirements (Classification Broof(t4) to BS EN 13501-5:2016).
BS EN 13501-5:2016 – When tested with a covering of 50mm thick concrete paving on 50mm high InStar plastic pedestal supports, or Dura Deck Resist composite decking on plastic pedestal supports with a 50mm ballast layer beneath a roof construction incorporating ProTherm Quantum® PLUS+ achieved a classification of Broof(t4) and as such is unrestricted by the National Building Regulations.
BS 476 Part 3: 2004 – When tested with a covering of 50mm thick concrete paving on 50mm high InStar plastic pedestal supports, or Dura Deck Resist composite decking on plastic pedestal supports with a 50mm ballast layer beneath a roof construction incorporating ProTherm Quantum® PLUS+ achieved a classification of EXT.FAA and as such is unrestricted by the National Building Regulations.
As a product in isolation
BS EN 13501-5:2016 – ProTherm Quantum® PLUS+ VIP Inverted Roof Insulation achieves Euro Class E performance.
See attached Product Data Sheet for further information.
For all applicable roofing systems contact Radmat Building Products and see
BBA certificate No. 20/5769.
| Description | Value |
| Appearance top/bottom | Anthracite (robotically spray applied coating) |
| Core | Fumed silica sand, fleece and foil wrapped and evacuated of air |
| Board Width mm* | 202, 302, 402, 502, 602 |
| Board Thickness mm* | 22, 27, 32, 37, 42, 47, 52, 57, 62, 67, 72, 77, 82, 87, 92, 97, 102 |
| Board Length mm* | 302, 402, 502, 602, 702, 802, 902, 1002 |
| Edge Profile | Square edge |
| Thermal Conductivity | 0.007 W/mK – 22-102 Declared value |
| Thermal Conductivity | 0.007 W/mK – 22-102 Design value |
| Delivery | Boxed |
* Panel sizes shown in bold are stocked items, all other dimensions are made to order and may be subject to additional lead time
| Downloads |
|---|
| BBA Pure |
| BBA Hybrid |
| BBA PermaQuik |
| Brochure |
| PDS |
| SDS |
| Standard Details 1 |
| Standard Details 2 |
Click on the items above to view or download information. To download multiple items as a zip file click + or simply click the check box to add to a collection.
Please Login before adding files to a collection.
